Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 5 Next »

 

General information

This functionality allows seats pre-assigment from the reservations module.

A Seat Map assigned to each equipment is created in the KASAT table that allows pre-assignment. When creating a flight through the Schedule module with an equipment with PRS, an inventory of Seat Map will be generated, creating an independent Seat Map for each flight / date generated.

Different features  can be assigned to each seat / row / column of the Seat Map that will then  be shown in the display (Seat Map Display). These are the  conditions for the corresponding pre-assignment, for example, seats with additional cost or enabled only for certain classes of Reservations.

The seats can be preassigned from the  PNR  creation according to the parameters configuration set in JJPRS.

Once the Flight Check-In is enabled, the Seat Map assigned to the Check-In and flight registration must have the same conditions as the one created in Schedule and assigned in the KASAT table. Both seat maps will be kept in sync with each other allowing them to continue pre-assigning seats from the reservation module as well as assigning seats through the WebCheck-In (v2) or counters. If there are discrepancies between both Seat Maps, while the flight is available in the Check-In, pre-assignment will be allowed only for those seats that exist in both Seat Maps in the same cabin.

A passenger with a  pre-assigned  seat in a reservation can be checked directly  through WebCheck-In or at counters. The seat can also be modified at the time of acceptance.

When modifying any  preassigned seats at the time of  Check-In, the system will release the pre-assigned seat but will not modify the SEAT element in  PNR. That is, visually, the PNR will remain with the preassigned seat even if it has been released.

A single Seat Map can only be assigned to a single KASAT equipment and the Seat Map number created will match the KASAT equipment to which it is related.

 Automatic seats re-accommodation  will be possible only in cases when an  equipment change occurs and the pre-assigned seat exists and is available in the new Seat Map. In cases where the same seat is not available, or in case of  flight  cancellation, the system will proceed to change the status of all SEAT elements to UN and place all  PNRs on  HDQ queue 55 and of the corresponding city for manual seat re-accommodation.

 

In case of creating, modifying, or deleting  Seat Maps already assigned to active flights, the system will allow  to  change  the same equipment  already assigned for the changes to be applied through Schedules.

 

 

Documentos para clientes

(warning) En una v2 de KPRS Líneas aéreas y Agencias se deberá agregar a medida que esté disponbile:

  • Configuración JJPRS
  • WebCheckin
  • Otros GDS
  • Ancillaries

 

 

 

Configuration (JJPRS)

 

In order to configure  KIU Pre  Reserved Seats module  you need to access JJPRS table so you indicate the basic preferences.

 

Duties 7 or  8 are required for set-up.

 

 

 

 

Enabling JJPRS table

This table will be enabled only when JJPRS table is activated  for  PRS  options 1 (without ancillaries) or 2 (with ancillaries).

If the option JJAIR / PRS is deactivated (N), when trying to visualize the JJPRS table, the system will respond SERVICE NOT AVAILABLE.

 

 

JJPRS
SERVICE NOT AVAILABLE

 

In the first instance, when enabling the JJPRS table by activating JJAIR / PRS, it will be created with default values.

 

 

 

 

JJPRS Table

  

In this first instance there are two configurable parameters in the Seats Pre-assignment Table. At the time of activation, default values will be assigned to each of the parameters.

 

 

 


[ENA]

ENABLE PRS

Number of days before flight departure when the seat pre-assignment will be available
Default: 90 days before departure

[DIS]

DISABLE PRS

Number of hours before flight departure when the seat pre-assignment will be available
Default: 2 hours before departure

 

 

 

 

Considerations:

 

  •  Seat Maps are created by the system, for each flight / date, at the time of equipment assignment (KASAT) that has  an designated Seat Map (KPRS)

  •  Parameters in this table define whether display and pre-assignment commands (4G) are allowed or not according to the flight  date of departure and the date on which the commands are performed.

  •  CRC or inventory commands (VST and VST / SS) can be executed at any time. The system will add a notification that the pre-assignment  is deactivated by this table

  • Definitions of the JJPRS table are applicable to the entire Host and all systems and channels that use pre-allocation

  • Values of the JJPRS table are valid from the moment the parameters are configured.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  • No labels